Why does the small signal analysis work? (Intuition)Small signal models of MOS amplifiersSmall-signal analysis of inductor/capacitorWhy does my ground current look like this (and why is my current so low)?MOSFET amplifier mid-point biasSimple circuit analysis with dependent sourceWhy does the signal MOSFET keep failing in this circuit?R in and R out mosfet calrificationInput/out impedance and voltage gainQuestion on MOSFET - small signal modelCan't figure out how book on Trannys gets hfe of CE amplifier when using T-Equivalent and Hybrid Pi Circuits
Finding files for which a command fails
Can produce flame be used to grapple, or as an unarmed strike, in the right circumstances?
What does "enim et" mean?
How to create a consistent feel for character names in a fantasy setting?
Pristine Bit Checking
If a centaur druid Wild Shapes into a Giant Elk, do their Charge features stack?
Synthetic Control Method
What happens when a metallic dragon and a chromatic dragon mate?
Check if two datetimes are between two others
How can I add custom success page
Manga about a female worker who got dragged into another world together with this high school girl and she was just told she's not needed anymore
Does the average primeness of natural numbers tend to zero?
"listening to me about as much as you're listening to this pole here"
Shall I use personal or official e-mail account when registering to external websites for work purpose?
"My colleague's body is amazing"
Calculate Levenshtein distance between two strings in Python
How many letters suffice to construct words with no repetition?
Could Giant Ground Sloths have been a good pack animal for the ancient Mayans?
How to manage monthly salary
Is there a familial term for apples and pears?
What are the advantages and disadvantages of running one shots compared to campaigns?
What is GPS' 19 year rollover and does it present a cybersecurity issue?
I see my dog run
Unbreakable Formation vs. Cry of the Carnarium
Why does the small signal analysis work? (Intuition)
Small signal models of MOS amplifiersSmall-signal analysis of inductor/capacitorWhy does my ground current look like this (and why is my current so low)?MOSFET amplifier mid-point biasSimple circuit analysis with dependent sourceWhy does the signal MOSFET keep failing in this circuit?R in and R out mosfet calrificationInput/out impedance and voltage gainQuestion on MOSFET - small signal modelCan't figure out how book on Trannys gets hfe of CE amplifier when using T-Equivalent and Hybrid Pi Circuits
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty margin-bottom:0;
$begingroup$
Consider the Large and small signal model of the MOSFET amplifier,
simulate this circuit – Schematic created using CircuitLab
How is this transformation valid, I get the linearization of the MOSFET, but then how can a source become a short and how can we reason the simplifications of other elements. I mean, the original circuit looks totally different from the small signal model. Please provide an intuitive answer, as I get the math part (i.e.) for small signal variations, the behavior of various elements are studied and then approximated, My question is how is this valid? For example, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle that we supply, similarly wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
Is there a non-mathematical explanation for shorting voltage source during small signal analysis?
mosfet circuit-analysis amplifier small-signal
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
$endgroup$
add a comment |
$begingroup$
Consider the Large and small signal model of the MOSFET amplifier,
simulate this circuit – Schematic created using CircuitLab
How is this transformation valid, I get the linearization of the MOSFET, but then how can a source become a short and how can we reason the simplifications of other elements. I mean, the original circuit looks totally different from the small signal model. Please provide an intuitive answer, as I get the math part (i.e.) for small signal variations, the behavior of various elements are studied and then approximated, My question is how is this valid? For example, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle that we supply, similarly wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
Is there a non-mathematical explanation for shorting voltage source during small signal analysis?
mosfet circuit-analysis amplifier small-signal
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
$endgroup$
$begingroup$
We assume ZERO impedance between VDD (or Vs) and Ground. Hence the need for bypass capacitors.
$endgroup$
– analogsystemsrf
18 hours ago
$begingroup$
Have you learned the Taylor series in math yet?
$endgroup$
– The Photon
17 hours ago
$begingroup$
Yeah, I did. but then, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I think I can answer that question without referring to the Taylor series, but the more general question in your title ("Why does the small signal analysis work?") basically comes down to the Taylor series.
$endgroup$
– The Photon
17 hours ago
add a comment |
$begingroup$
Consider the Large and small signal model of the MOSFET amplifier,
simulate this circuit – Schematic created using CircuitLab
How is this transformation valid, I get the linearization of the MOSFET, but then how can a source become a short and how can we reason the simplifications of other elements. I mean, the original circuit looks totally different from the small signal model. Please provide an intuitive answer, as I get the math part (i.e.) for small signal variations, the behavior of various elements are studied and then approximated, My question is how is this valid? For example, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle that we supply, similarly wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
Is there a non-mathematical explanation for shorting voltage source during small signal analysis?
mosfet circuit-analysis amplifier small-signal
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
$endgroup$
Consider the Large and small signal model of the MOSFET amplifier,
simulate this circuit – Schematic created using CircuitLab
How is this transformation valid, I get the linearization of the MOSFET, but then how can a source become a short and how can we reason the simplifications of other elements. I mean, the original circuit looks totally different from the small signal model. Please provide an intuitive answer, as I get the math part (i.e.) for small signal variations, the behavior of various elements are studied and then approximated, My question is how is this valid? For example, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle that we supply, similarly wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
Is there a non-mathematical explanation for shorting voltage source during small signal analysis?
mosfet circuit-analysis amplifier small-signal
mosfet circuit-analysis amplifier small-signal
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
edited 17 hours ago
Aravindh Vasu
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
asked 18 hours ago
Aravindh VasuAravindh Vasu
305
305
$begingroup$
We assume ZERO impedance between VDD (or Vs) and Ground. Hence the need for bypass capacitors.
$endgroup$
– analogsystemsrf
18 hours ago
$begingroup$
Have you learned the Taylor series in math yet?
$endgroup$
– The Photon
17 hours ago
$begingroup$
Yeah, I did. but then, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I think I can answer that question without referring to the Taylor series, but the more general question in your title ("Why does the small signal analysis work?") basically comes down to the Taylor series.
$endgroup$
– The Photon
17 hours ago
add a comment |
$begingroup$
We assume ZERO impedance between VDD (or Vs) and Ground. Hence the need for bypass capacitors.
$endgroup$
– analogsystemsrf
18 hours ago
$begingroup$
Have you learned the Taylor series in math yet?
$endgroup$
– The Photon
17 hours ago
$begingroup$
Yeah, I did. but then, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I think I can answer that question without referring to the Taylor series, but the more general question in your title ("Why does the small signal analysis work?") basically comes down to the Taylor series.
$endgroup$
– The Photon
17 hours ago
$begingroup$
We assume ZERO impedance between VDD (or Vs) and Ground. Hence the need for bypass capacitors.
$endgroup$
– analogsystemsrf
18 hours ago
$begingroup$
We assume ZERO impedance between VDD (or Vs) and Ground. Hence the need for bypass capacitors.
$endgroup$
– analogsystemsrf
18 hours ago
$begingroup$
Have you learned the Taylor series in math yet?
$endgroup$
– The Photon
17 hours ago
$begingroup$
Have you learned the Taylor series in math yet?
$endgroup$
– The Photon
17 hours ago
$begingroup$
Yeah, I did. but then, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
Yeah, I did. but then, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I think I can answer that question without referring to the Taylor series, but the more general question in your title ("Why does the small signal analysis work?") basically comes down to the Taylor series.
$endgroup$
– The Photon
17 hours ago
$begingroup$
I think I can answer that question without referring to the Taylor series, but the more general question in your title ("Why does the small signal analysis work?") basically comes down to the Taylor series.
$endgroup$
– The Photon
17 hours ago
add a comment |
2 Answers
2
active
oldest
votes
$begingroup$
In small signal-analysis, the behavior of a non-linear device is approximated as linear about a DC operating point (Quiescent point). Basically we put in a small 'wiggle' signal that doesn't change things to much from the DC level. With a linear model we can apply the principle of superposition.
That is, the total response of the system can be viewed as the sum of the responses to each source individually. In your left picture there are two sources, a signal input from the left, and what is usually a DC power supply at the top. In the right hand picture, this source is simply being zeroed so the response to the input signal can be more easily determined. Therefore it is replaced by a short circuit to ground.
The actual behavior of the circuit is then this response, plus the response to the DC source alone.
answered 18 hours ago
jramsay42jramsay42
585127
$endgroup$
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
add a comment |
$begingroup$
wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
When we talk about the small signal circuit, we are asking how much will the voltages and currents in the circuit change due to a small change in some input excitation (usually due to a voltage or current source).
If you change the input voltage to a circuit that contains an ideal voltage source, the voltage across that source doesn't change at all (that's why we call it ideal).
Since the voltage change is 0, its equivalent component in the small-signal circuit is a 0 V source.
The voltage assigned to the source (or any other component in the circuit) in a small-signal model is not its actual voltage, it's the voltage change due to the small-signal excitation.
answered 17 hours ago
The PhotonThe Photon
87.1k398203
$endgroup$
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
2
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
);
);
, "mathjax-editing");
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f431341%2fwhy-does-the-small-signal-analysis-work-intuition%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
2 Answers
2
active
oldest
votes
2 Answers
2
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
In small signal-analysis, the behavior of a non-linear device is approximated as linear about a DC operating point (Quiescent point). Basically we put in a small 'wiggle' signal that doesn't change things to much from the DC level. With a linear model we can apply the principle of superposition.
That is, the total response of the system can be viewed as the sum of the responses to each source individually. In your left picture there are two sources, a signal input from the left, and what is usually a DC power supply at the top. In the right hand picture, this source is simply being zeroed so the response to the input signal can be more easily determined. Therefore it is replaced by a short circuit to ground.
The actual behavior of the circuit is then this response, plus the response to the DC source alone.
answered 18 hours ago
jramsay42jramsay42
585127
$endgroup$
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
add a comment |
$begingroup$
In small signal-analysis, the behavior of a non-linear device is approximated as linear about a DC operating point (Quiescent point). Basically we put in a small 'wiggle' signal that doesn't change things to much from the DC level. With a linear model we can apply the principle of superposition.
That is, the total response of the system can be viewed as the sum of the responses to each source individually. In your left picture there are two sources, a signal input from the left, and what is usually a DC power supply at the top. In the right hand picture, this source is simply being zeroed so the response to the input signal can be more easily determined. Therefore it is replaced by a short circuit to ground.
The actual behavior of the circuit is then this response, plus the response to the DC source alone.
answered 18 hours ago
jramsay42jramsay42
585127
$endgroup$
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
add a comment |
$begingroup$
In small signal-analysis, the behavior of a non-linear device is approximated as linear about a DC operating point (Quiescent point). Basically we put in a small 'wiggle' signal that doesn't change things to much from the DC level. With a linear model we can apply the principle of superposition.
That is, the total response of the system can be viewed as the sum of the responses to each source individually. In your left picture there are two sources, a signal input from the left, and what is usually a DC power supply at the top. In the right hand picture, this source is simply being zeroed so the response to the input signal can be more easily determined. Therefore it is replaced by a short circuit to ground.
The actual behavior of the circuit is then this response, plus the response to the DC source alone.
answered 18 hours ago
jramsay42jramsay42
585127
$endgroup$
In small signal-analysis, the behavior of a non-linear device is approximated as linear about a DC operating point (Quiescent point). Basically we put in a small 'wiggle' signal that doesn't change things to much from the DC level. With a linear model we can apply the principle of superposition.
That is, the total response of the system can be viewed as the sum of the responses to each source individually. In your left picture there are two sources, a signal input from the left, and what is usually a DC power supply at the top. In the right hand picture, this source is simply being zeroed so the response to the input signal can be more easily determined. Therefore it is replaced by a short circuit to ground.
The actual behavior of the circuit is then this response, plus the response to the DC source alone.
answered 18 hours ago
jramsay42jramsay42
585127
answered 18 hours ago
jramsay42jramsay42
585127
answered 18 hours ago
jramsay42jramsay42
585127
answered 18 hours ago
jramsay42jramsay42
585127
585127
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
add a comment |
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
So, do you say that the DC source is removed to apply superposition? Wait, the small signal model of a resistor is simply the resistor itself because the resistor produces a corresponding voltage drop during the small wiggle, similarly wouldn't the Voltage source be unaltered during the 'wiggle'?
$endgroup$
– Aravindh Vasu
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
@AravindhVasu, the small signal equivalent of a linear resistor is just the same resistor. But the small signal equivalent of a nonlinear resistor (for example, a PN-junction diode considered in the low-frequency limit) is a different resistor at every operating point.
$endgroup$
– The Photon
18 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
Okay, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I get the fact that we are linearly approximating a device , but I just cant digest(reason) vanishing the source.
$endgroup$
– Aravindh Vasu
17 hours ago
add a comment |
$begingroup$
wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
When we talk about the small signal circuit, we are asking how much will the voltages and currents in the circuit change due to a small change in some input excitation (usually due to a voltage or current source).
If you change the input voltage to a circuit that contains an ideal voltage source, the voltage across that source doesn't change at all (that's why we call it ideal).
Since the voltage change is 0, its equivalent component in the small-signal circuit is a 0 V source.
The voltage assigned to the source (or any other component in the circuit) in a small-signal model is not its actual voltage, it's the voltage change due to the small-signal excitation.
answered 17 hours ago
The PhotonThe Photon
87.1k398203
$endgroup$
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
2
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
add a comment |
$begingroup$
wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
When we talk about the small signal circuit, we are asking how much will the voltages and currents in the circuit change due to a small change in some input excitation (usually due to a voltage or current source).
If you change the input voltage to a circuit that contains an ideal voltage source, the voltage across that source doesn't change at all (that's why we call it ideal).
Since the voltage change is 0, its equivalent component in the small-signal circuit is a 0 V source.
The voltage assigned to the source (or any other component in the circuit) in a small-signal model is not its actual voltage, it's the voltage change due to the small-signal excitation.
answered 17 hours ago
The PhotonThe Photon
87.1k398203
$endgroup$
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
2
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
add a comment |
$begingroup$
wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
When we talk about the small signal circuit, we are asking how much will the voltages and currents in the circuit change due to a small change in some input excitation (usually due to a voltage or current source).
If you change the input voltage to a circuit that contains an ideal voltage source, the voltage across that source doesn't change at all (that's why we call it ideal).
Since the voltage change is 0, its equivalent component in the small-signal circuit is a 0 V source.
The voltage assigned to the source (or any other component in the circuit) in a small-signal model is not its actual voltage, it's the voltage change due to the small-signal excitation.
answered 17 hours ago
The PhotonThe Photon
87.1k398203
$endgroup$
wouldn't the Voltage source be unaltered during the 'wiggle', so shouldn't the small signal model of the Voltage source be itself ?
When we talk about the small signal circuit, we are asking how much will the voltages and currents in the circuit change due to a small change in some input excitation (usually due to a voltage or current source).
If you change the input voltage to a circuit that contains an ideal voltage source, the voltage across that source doesn't change at all (that's why we call it ideal).
Since the voltage change is 0, its equivalent component in the small-signal circuit is a 0 V source.
The voltage assigned to the source (or any other component in the circuit) in a small-signal model is not its actual voltage, it's the voltage change due to the small-signal excitation.
answered 17 hours ago
The PhotonThe Photon
87.1k398203
edited 17 hours ago
answered 17 hours ago
The PhotonThe Photon
87.1k398203
answered 17 hours ago
The PhotonThe Photon
87.1k398203
answered 17 hours ago
The PhotonThe Photon
87.1k398203
87.1k398203
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
2
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
add a comment |
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
2
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
But wouldn't shorting the DC voltage change the bias point and stuff? Please Bare with me here :)
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
$begingroup$
You don't short the voltage in the DC model used to find the operating point, only in the small-signal model used to find the effects of small changes in the inputs.
$endgroup$
– The Photon
17 hours ago
2
2
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
Yeah okay, so to study small changes in the input, we form a separate linear circuit by substituting for each component its small signal component, which is the response that the specific component gives during the small wiggle, and the voltage source doesn't contribute anything to the change in output, so we short it ,am I right?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
$begingroup$
@AravindhVasu, yes, that's it.
$endgroup$
– The Photon
17 hours ago
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f431341%2fwhy-does-the-small-signal-analysis-work-intuition%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
We assume ZERO impedance between VDD (or Vs) and Ground. Hence the need for bypass capacitors.
$endgroup$
– analogsystemsrf
18 hours ago
$begingroup$
Have you learned the Taylor series in math yet?
$endgroup$
– The Photon
17 hours ago
$begingroup$
Yeah, I did. but then, is there a non-mathematical explanation for shorting voltage source during small signal analysis?
$endgroup$
– Aravindh Vasu
17 hours ago
$begingroup$
I think I can answer that question without referring to the Taylor series, but the more general question in your title ("Why does the small signal analysis work?") basically comes down to the Taylor series.
$endgroup$
– The Photon
17 hours ago